How to Fix Lloyd Washing Machine Error U19 (PCB Inverter Issue)

What error U19 means

Error U19 on a Lloyd top load fully automatic washing machine falls within the U00 to U21 range that Lloyd's user manual lists as 'Issue due to PCB inverter'. The manual (a Havells brand; the table is in the manual for models GLWT855N12CB, GLWT855N12SS, GLWT805N12CB, GLWT805N12SS and GLWT755N12CB, the Novanté IoT i H series) gives one instruction for the whole U00 to U21 range: power off the machine, it will resolve itself; if it doesn't resolve itself, call the Lloyd service centre. The manual does not describe U19 separately from the other U codes, so this page treats it as the manual does: an inverter board fault that the machine may clear on a restart and that otherwise needs a service visit.

Why error U19 happens on a Lloyd Washing Machine

On a Lloyd Washing Machine, error U19typically resolves to one of three root-cause categories. They’re ordered cheapest-to-verify first — start at the top and only escalate if the first cause is ruled out.

• Mechanical: blockage, obstruction, or worn moving part. A common cause across Lloyd Washing Machines in India — drain pumps, door seals and lint filters wear with daily cycles. Our step-by-step fix below targets this category first because it’s the cheapest to verify and resolvereports.
• Electrical: voltage spike, sensor fault, or PCB anomaly. India’s grid carries more voltage fluctuation than many appliance design tolerances assume, and a routine surge or sag can be enough to throw U19. If you’ve had recent voltage events (lights flickering, AC tripping), start your investigation here. A working stabilizer prevents this entire category.
• Software / configuration: stuck child-lock, demo-mode, or pending firmware reset.Less common but the cheapest fix when it applies — a 60-second factory reset clears it. We list this last because it’s rarely the actual cause, but check it before disassembling anything.

Safety first

Step-by-step fix

1. 1

   Step 1

   Power off the machine

   This is the manual's first and only home step for the U codes. Switch the machine off with the power button, then switch it off at the wall socket as well. Leave it off for a few minutes so the inverter board fully powers down rather than just going to standby.

2. 2

   Step 2

   Wait for a steady power supply

   If the lights in the house are flickering, a power cut has just ended, or your area is in a low-voltage period, wait until the supply settles before switching back on. The manual lists separate codes, FrH and FrL, for abnormal high and low voltage at the electronic controller, so unstable supply is a known trigger for controller-side errors on these machines. This is general practice and does not replace the manual's instruction.

3. 3

   Step 3

   Switch on and restart the programme

   Switch on at the socket, press the power button, select the programme and press Start/Pause. The manual says the issue 'will resolve itself' after a power-off, so a clean restart is the test. Let the machine run through at least the fill and wash stages; U codes relate to the inverter that drives the motor, so the fault would show when the motor is asked to run.

4. 4

   Step 4

   Call Lloyd service if U19 returns

   If U19 (or any other U00 to U21 code) appears again after a full power-off and restart, the manual's instruction is to call the Lloyd service centre. Tell them the exact code shown and your model number from the sticker on the back or inside the lid. Do not open the machine; the inverter PCB carries mains voltage and is a service-only part.

Fixed it? Protect it next time. See an extended warranty plan for your Washing Machine →

Common mistakes Lloyd Washing Machine owners make with error U19

These six anti-patterns turn a routine 30-minute fix into a costly repair or warranty void. Read before starting.

• Forcing a stuck door, lid, or panel. A Lloyd Washing Machine uses interlocked sensors that hold the unit shut while it is in a fault state. Forcing it usually breaks the latch or sensor — turning a small part replacement into a full service call. If the door won’t open, run the safety-disconnect step first, then try again.
• Repeated unplug-and-replug as a “reset” ritual. Cycling power three or four times without diagnosing the underlying cause stresses the PCB and can convert a soft fault into a permanent firmware-corruption code. Reset once, observe whether the error returns immediately, then move to actual diagnosis if it does.
• Pouring water (or any liquid) into electronics-adjacent areas to flush a blockage.Even a small amount near the PCB or main wiring harness can cause permanent damage that voids warranty. The unit’s drainage paths exist for a reason; if a blockage isn’t cleared by the manual procedure, it isn’t getting cleared by improvisation either.
• Skipping the safety-disconnect step.“I’ll just check quickly” is the most expensive sentence in appliance repair. Working live on a 230V circuit (especially with a hot or wet appliance) carries real shock risk and instantly voids any warranty claim. Disconnect, wait two minutes for capacitor drain, then proceed.
• Buying counterfeit replacement parts on Amazon.in. Red flags: price below 60% of Lloyd authorised price, generic packaging without a model-compatibility list, seller name that doesn’t match a known Lloyd parts distributor, listings dated within the last 30 days with no reviews. Counterfeit parts often work for 2-3 weeks then fail with a different error, costing you double.
• Calling an “independent” technician for a warranty-covered unit. Indian appliances under Lloyd warranty must be serviced by authorised technicians or the warranty voids permanently. Even if the warranty is expired, third-party local technicians often replace working parts to inflate the bill — verify each part swap by asking to see the failure on the old part before they install the new one.

Preventing future U19 on your Lloyd Washing Machine

The fix above resolves the current instance. These five maintenance habits prevent it from coming back, specific to Lloyd Washing Machines in Indian operating conditions (hard water, voltage variability, monsoon humidity).

• Monthly: clean the drain filter and inlet strainer. Hard-water deposits and everyday debris are a frequent cause of recurring U19 in India, and a few minutes each month is the cheapest way to avoid a repeat.
• Quarterly: descale water-touching components. Use food-grade citric acid or a Lloyd approved descaler for hard-water regions (Bangalore, Hyderabad, large parts of Maharashtra and Tamil Nadu). Skipping this in a hard-water zone shortens the life of the heating and water-touching parts.
• Run the unit through a working stabilizer. A mainline stabilizer sized for Washing Machines is the cheapest protection against voltage-induced U19 occurrences. The MCB on your distribution board is not a substitute — it trips on overload, not on under-voltage or surge.
• Decide AMC vs DIY honestly. Compare the LloydAMC quote against what you have actually spent on service. If your unit is >5 years old and you’ve had two service calls in the last 18 months, an AMC usually pays for itself. Younger units with no service history: DIY plus stabilizer is cheaper.
• Watch monthly for early-warning signs. Unusual noise during a specific cycle phase, water spotting, mild burning smell — any of these means a service call within a week, not a wait-and-see month. Catching U19-precursor symptoms early turns a major repair into a routine maintenance visit.

If error U19 returns within 30 days of completing the fix above, escalate directly to Lloydauthorised service — repeat patterns within a month indicate a deeper fault (worn bearing, failing PCB, leak that wasn’t fully identified) that surface-level repair won’t resolve. Document the dates and circumstances of each occurrence; the service centre will use this to prioritize root-cause investigation.