How to Turn Off Child Lock (CL) on a Godrej Washing Machine

What error CL means

CL on a Godrej washing machine display means Child Lock is active. This is a status indication, not a fault. When Child Lock is on, 'CL' shows on the display and all control-panel buttons are inactive, so the machine appears unresponsive and many owners assume the panel has failed. It is shown on top-load models fitted with a digital display. Child Lock is switched on and off with a two-key combination held for 2 seconds — WATER LEVEL together with PROGRAM on WT EON Allure models, and Wash Cycle together with '+ Wash' on EON Velvet Steam models. It is usually enabled deliberately, or by a child or an accidental press hitting that combination during a cycle.

Why error CL happens on a Godrej Washing Machine

On a Godrej Washing Machine, error CLtypically resolves to one of three root-cause categories. They’re ordered cheapest-to-verify first — start at the top and only escalate if the first cause is ruled out.

• Mechanical: blockage, obstruction, or worn moving part. A common cause across Godrej Washing Machines in India — drain pumps, door seals and lint filters wear with daily cycles. Our step-by-step fix below targets this category first because it’s the cheapest to verify and resolvereports.
• Electrical: voltage spike, sensor fault, or PCB anomaly. India’s grid carries more voltage fluctuation than many appliance design tolerances assume, and a routine surge or sag can be enough to throw CL. If you’ve had recent voltage events (lights flickering, AC tripping), start your investigation here. A working stabilizer prevents this entire category.
• Software / configuration: stuck child-lock, demo-mode, or pending firmware reset.Less common but the cheapest fix when it applies — a 60-second factory reset clears it. We list this last because it’s rarely the actual cause, but check it before disassembling anything.

Safety first

Step-by-step fix

1. 1

   Step 1

   Confirm the display is showing CL and not something else

   Look closely at the display. CL is two characters and appears on its own. If you are seeing an E-code, an H-code or a flashing indicator instead, this is not Child Lock and a different guide applies.

   Pro tip: Photograph the display. It makes identifying the characters much easier than squinting at a small panel, and it is useful if you do end up calling support.

2. 2

   Step 2

   Identify which Godrej series your machine belongs to

   Check the model number on the rating plate, usually on the rear panel or under the lid rim, and match it to the badge on the front. The key combination that toggles Child Lock differs between ranges, so getting this right first saves you pressing the wrong buttons.

   Pro tip: Save a photo of the rating plate on your phone. It is the single most useful thing to have when looking up anything about the machine later.

3. 3

   Step 3

   Press the correct two-key combination for 2 seconds

   On WT EON Allure models, press and hold WATER LEVEL and PROGRAM together for 2 seconds. On EON Velvet Steam models, press and hold Wash Cycle and '+ Wash' together for 2 seconds. Hold both keys down at the same time for the full 2 seconds — a quick tap will not toggle the lock.

   Pro tip: Press both keys firmly and simultaneously with two fingers. Pressing one slightly before the other is the most common reason the combination appears not to work.

4. 4

   Step 4

   Confirm CL has cleared and the panel responds

   CL should disappear from the display. Press any other button — a programme selector or the water level key — and confirm the machine now responds. If it does, the panel was never faulty and there is nothing further to do.

   Pro tip: If a cycle was running when Child Lock was engaged, it will have continued normally. Child Lock disables the buttons, not the wash.

5. 5

   Step 5

   If CL will not clear, check for a stuck key

   Unplug the machine. Wipe the control panel with a barely damp cloth and dry it thoroughly, paying attention to the two lock keys and the gaps around them where detergent and grime collect. Press each key individually and feel whether any one stays depressed or feels mushy compared with the others. Plug back in and try the combination again.

   Caution: Never spray water or cleaner directly at the panel, and never lever a key up with a metal tool.

   Pro tip: A sticking or shorted membrane key holding the lock combination down is a listed cause of CL that will not clear. If one key clearly feels different from the rest, that is what to report.

6. 6

   Step 6

   Power-cycle as a last check

   Switch off at the wall socket, unplug for three minutes, then plug back in and try the two-key combination once more. If CL still will not clear and one or more keys feel stuck or unresponsive, the membrane panel needs a technician.

   Pro tip: Note which keys feel wrong before you call. A membrane panel is a stocked part for current models and a technician can usually confirm the diagnosis in one visit.

Repair costs adding up? Compare top-rated Washing Machines on PakkaPick →

Common mistakes Godrej Washing Machine owners make with error CL

These six anti-patterns turn a routine 30-minute fix into a costly repair or warranty void. Read before starting.

• Forcing a stuck door, lid, or panel. A Godrej Washing Machine uses interlocked sensors that hold the unit shut while it is in a fault state. Forcing it usually breaks the latch or sensor — turning a small part replacement into a full service call. If the door won’t open, run the safety-disconnect step first, then try again.
• Repeated unplug-and-replug as a “reset” ritual. Cycling power three or four times without diagnosing the underlying cause stresses the PCB and can convert a soft fault into a permanent firmware-corruption code. Reset once, observe whether the error returns immediately, then move to actual diagnosis if it does.
• Pouring water (or any liquid) into electronics-adjacent areas to flush a blockage.Even a small amount near the PCB or main wiring harness can cause permanent damage that voids warranty. The unit’s drainage paths exist for a reason; if a blockage isn’t cleared by the manual procedure, it isn’t getting cleared by improvisation either.
• Skipping the safety-disconnect step.“I’ll just check quickly” is the most expensive sentence in appliance repair. Working live on a 230V circuit (especially with a hot or wet appliance) carries real shock risk and instantly voids any warranty claim. Disconnect, wait two minutes for capacitor drain, then proceed.
• Buying counterfeit replacement parts on Amazon.in. Red flags: price below 60% of Godrej authorised price, generic packaging without a model-compatibility list, seller name that doesn’t match a known Godrej parts distributor, listings dated within the last 30 days with no reviews. Counterfeit parts often work for 2-3 weeks then fail with a different error, costing you double.
• Calling an “independent” technician for a warranty-covered unit. Indian appliances under Godrej warranty must be serviced by authorised technicians or the warranty voids permanently. Even if the warranty is expired, third-party local technicians often replace working parts to inflate the bill — verify each part swap by asking to see the failure on the old part before they install the new one.

Preventing future CL on your Godrej Washing Machine

The fix above resolves the current instance. These five maintenance habits prevent it from coming back, specific to Godrej Washing Machines in Indian operating conditions (hard water, voltage variability, monsoon humidity).

• Monthly: clean the drain filter and inlet strainer. Hard-water deposits and everyday debris are a frequent cause of recurring CL in India, and a few minutes each month is the cheapest way to avoid a repeat.
• Quarterly: descale water-touching components. Use food-grade citric acid or a Godrej approved descaler for hard-water regions (Bangalore, Hyderabad, large parts of Maharashtra and Tamil Nadu). Skipping this in a hard-water zone shortens the life of the heating and water-touching parts.
• Run the unit through a working stabilizer. A mainline stabilizer sized for Washing Machines is the cheapest protection against voltage-induced CL occurrences. The MCB on your distribution board is not a substitute — it trips on overload, not on under-voltage or surge.
• Decide AMC vs DIY honestly. Compare the GodrejAMC quote against what you have actually spent on service. If your unit is >5 years old and you’ve had two service calls in the last 18 months, an AMC usually pays for itself. Younger units with no service history: DIY plus stabilizer is cheaper.
• Watch monthly for early-warning signs. Unusual noise during a specific cycle phase, water spotting, mild burning smell — any of these means a service call within a week, not a wait-and-see month. Catching CL-precursor symptoms early turns a major repair into a routine maintenance visit.

If error CL returns within 30 days of completing the fix above, escalate directly to Godrejauthorised service — repeat patterns within a month indicate a deeper fault (worn bearing, failing PCB, leak that wasn’t fully identified) that surface-level repair won’t resolve. Document the dates and circumstances of each occurrence; the service centre will use this to prioritize root-cause investigation.