How to Fix Godrej Washing Machine Error EE

What error EE means

Error EE on a Godrej fully automatic top-load washing machine (WT EON / WTEON series) is a water level sensing error. The machine's water-level sensor — a pressure-type switch fed by an air hose from the tub — is not reporting a valid water level, so the controller cannot tell how full the drum is and halts the cycle. Because every fill, wash and spin decision depends on that reading, the machine stops rather than guess. The usual causes are a kinked, split, blocked or detached air hose, a sludge-blocked air trap chamber at the base of the tub, a drain hose sitting at the wrong height, a failed pressure switch, or a transient control-board glitch after a power dip.

Why error EE happens on a Godrej Washing Machine

On a Godrej Washing Machine, error EEtypically resolves to one of three root-cause categories. They’re ordered cheapest-to-verify first — start at the top and only escalate if the first cause is ruled out.

• Mechanical: blockage, obstruction, or worn moving part. A common cause across Godrej Washing Machines in India — drain pumps, door seals and lint filters wear with daily cycles. Our step-by-step fix below targets this category first because it’s the cheapest to verify and resolvereports.
• Electrical: voltage spike, sensor fault, or PCB anomaly. India’s grid carries more voltage fluctuation than many appliance design tolerances assume, and a routine surge or sag can be enough to throw EE. If you’ve had recent voltage events (lights flickering, AC tripping), start your investigation here. A working stabilizer prevents this entire category.
• Software / configuration: stuck child-lock, demo-mode, or pending firmware reset.Less common but the cheapest fix when it applies — a 60-second factory reset clears it. We list this last because it’s rarely the actual cause, but check it before disassembling anything.

Safety first

Step-by-step fix

1. 1

   Step 1

   Power-cycle the machine completely

   Switch the machine off at the wall socket, pull the plug out, and leave it unplugged for at least three minutes so the control board fully discharges. Plug it back in, select a normal wash and start it. Watch whether the drum begins filling and whether EE returns.

   Pro tip: A quick off-on at the front panel is not the same thing. The board has to lose power at the plug to reset a glitch caused by a voltage dip.

2. 2

   Step 2

   Set the drain hose to the correct height

   Look at where the drain hose ends. It must not lie on the floor or run downhill into an open drain, and it must not be pushed deep into a standpipe or wedged high above the machine. Route it so the hose end sits roughly level with the height Godrej marks on the back of your machine, and make sure no part of the run is submerged in a bucket of water.

   Caution: Do not seal the hose into the drain pipe with tape or putty. The drain outlet needs an air gap or the machine will siphon.

   Pro tip: A hose end that sits too low siphons water out as fast as the machine fills it, so the tub never builds a readable water column — a classic cause of EE that needs no parts at all.

3. 3

   Step 3

   Check for anything blocking the tub outlet or filter

   Unplug the machine. Open the drain filter or debris trap and clear out lint, thread, coins and hair. Detergent sludge and lint packed around the base of the tub can also block the small air-trap chamber that feeds the sensor, and clearing the filter is the easiest part of that path to reach without opening the cabinet.

   Pro tip: If you use heavy detergent doses or wash a lot of cotton sarees and bedsheets, run an empty hot tub-clean cycle monthly to keep sludge from building up.

4. 4

   Step 4

   Inspect the air hose between the tub and the sensor

   With the machine unplugged and empty, remove the rear service panel or the top panel screws to expose the small clear or black air hose that runs from the base of the tub up to the water-level pressure switch. Follow the whole length. Straighten any kink, look for splits or brittle cracks, and check that both ends are pushed fully onto their spigots and clipped. Reseat anything loose.

   Caution: Take a photo before you disconnect anything, and do not pull on the loom of coloured wires going into the pressure switch — those carry mains-referenced signals to the board.

   Pro tip: If the hose is wet inside or has water sitting in a low loop, blow it clear and re-route it so it rises continuously from the tub to the sensor with no dip.

5. 5

   Step 5

   Clear the air trap at the base of the tub

   Where the air hose meets the tub there is a small chamber — the air trap — that converts water level into air pressure. Pull the hose off that spigot and check the port for scale, sludge or a lint plug. Flush it with warm water and clear it with a soft pipe cleaner. Push the hose back on fully and refit the clip.

   Caution: Do not poke a wire or screwdriver into the port. Puncturing the tub wall turns a sensor fault into a leaking tub.

   Pro tip: In borewell-water homes this port furs up with white scale. A weak descaling soak on the removed hose, followed by a thorough rinse, restores the air path.

6. 6

   Step 6

   Reassemble and run a test fill

   Refit every panel and screw you removed, plug the machine back in, open the tap and start a normal wash. Watch the fill: the water should rise steadily and the machine should move on to wash without displaying EE. If EE returns with a clear, correctly routed air hose and a clean air trap, the pressure switch or its input circuit on the board is at fault and needs a technician.

   Pro tip: Note at exactly which point EE appears — during fill, at the end of fill, or during drain. Telling the technician that narrows the diagnosis considerably.

Repair costs adding up? Compare top-rated Washing Machines on PakkaPick →

Common mistakes Godrej Washing Machine owners make with error EE

These six anti-patterns turn a routine 30-minute fix into a costly repair or warranty void. Read before starting.

• Forcing a stuck door, lid, or panel. A Godrej Washing Machine uses interlocked sensors that hold the unit shut while it is in a fault state. Forcing it usually breaks the latch or sensor — turning a small part replacement into a full service call. If the door won’t open, run the safety-disconnect step first, then try again.
• Repeated unplug-and-replug as a “reset” ritual. Cycling power three or four times without diagnosing the underlying cause stresses the PCB and can convert a soft fault into a permanent firmware-corruption code. Reset once, observe whether the error returns immediately, then move to actual diagnosis if it does.
• Pouring water (or any liquid) into electronics-adjacent areas to flush a blockage.Even a small amount near the PCB or main wiring harness can cause permanent damage that voids warranty. The unit’s drainage paths exist for a reason; if a blockage isn’t cleared by the manual procedure, it isn’t getting cleared by improvisation either.
• Skipping the safety-disconnect step.“I’ll just check quickly” is the most expensive sentence in appliance repair. Working live on a 230V circuit (especially with a hot or wet appliance) carries real shock risk and instantly voids any warranty claim. Disconnect, wait two minutes for capacitor drain, then proceed.
• Buying counterfeit replacement parts on Amazon.in. Red flags: price below 60% of Godrej authorised price, generic packaging without a model-compatibility list, seller name that doesn’t match a known Godrej parts distributor, listings dated within the last 30 days with no reviews. Counterfeit parts often work for 2-3 weeks then fail with a different error, costing you double.
• Calling an “independent” technician for a warranty-covered unit. Indian appliances under Godrej warranty must be serviced by authorised technicians or the warranty voids permanently. Even if the warranty is expired, third-party local technicians often replace working parts to inflate the bill — verify each part swap by asking to see the failure on the old part before they install the new one.

Preventing future EE on your Godrej Washing Machine

The fix above resolves the current instance. These five maintenance habits prevent it from coming back, specific to Godrej Washing Machines in Indian operating conditions (hard water, voltage variability, monsoon humidity).

• Monthly: clean the drain filter and inlet strainer. Hard-water deposits and everyday debris are a frequent cause of recurring EE in India, and a few minutes each month is the cheapest way to avoid a repeat.
• Quarterly: descale water-touching components. Use food-grade citric acid or a Godrej approved descaler for hard-water regions (Bangalore, Hyderabad, large parts of Maharashtra and Tamil Nadu). Skipping this in a hard-water zone shortens the life of the heating and water-touching parts.
• Run the unit through a working stabilizer. A mainline stabilizer sized for Washing Machines is the cheapest protection against voltage-induced EE occurrences. The MCB on your distribution board is not a substitute — it trips on overload, not on under-voltage or surge.
• Decide AMC vs DIY honestly. Compare the GodrejAMC quote against what you have actually spent on service. If your unit is >5 years old and you’ve had two service calls in the last 18 months, an AMC usually pays for itself. Younger units with no service history: DIY plus stabilizer is cheaper.
• Watch monthly for early-warning signs. Unusual noise during a specific cycle phase, water spotting, mild burning smell — any of these means a service call within a week, not a wait-and-see month. Catching EE-precursor symptoms early turns a major repair into a routine maintenance visit.

If error EE returns within 30 days of completing the fix above, escalate directly to Godrejauthorised service — repeat patterns within a month indicate a deeper fault (worn bearing, failing PCB, leak that wasn’t fully identified) that surface-level repair won’t resolve. Document the dates and circumstances of each occurrence; the service centre will use this to prioritize root-cause investigation.