How to Fix Godrej Washing Machine Error F6 (Low Voltage)

What error F6 means

Error F6 on a Godrej Eon fully automatic top load washing machine means 'Low voltage'. Godrej's own error table ('Error Codes And Handling') says: 'Turn the machine OFF From the main supply and restart it again after 5 min. This error is basically due to low voltage supply at your outlet, it should disappear automatically when voltage supply is back to normal.' The table is printed in the user manuals for the Godrej Eon Adora fully automatic top load range (WTEON ADA 80 5.0 FEFN, WTEON ADAC 80 5.0 FEFN, WTEON ADAC 80 5.0 FEFH, WTEON ADA 95 5.0 FEFH, WTEON ADA 10 5.0 FEFH, WTEON ADA 11 5.0 FEFH) and the Eon Rhine top load range (WTEON RHN 10 5.0 FEEH, WTEON RHN 12 5.0 FEEH, WTEON RHN 10 FT GLGR, WTEON RHN 12 FT GLGR). Other Godrej top load models show the same condition with a different code: their manuals list EL for input voltage below 160V (WTEON ALR C 70 5.0 / WTEON AL CLH 70 5.0 range) or below 150 V (Eon Velvet range). The Adora and Rhine manuals give no voltage figure for F6.

Why error F6 happens on a Godrej Washing Machine

On a Godrej Washing Machine, error F6typically resolves to one of three root-cause categories. They’re ordered cheapest-to-verify first — start at the top and only escalate if the first cause is ruled out.

• Mechanical: blockage, obstruction, or worn moving part. A common cause across Godrej Washing Machines in India — drain pumps, door seals and lint filters wear with daily cycles. Our step-by-step fix below targets this category first because it’s the cheapest to verify and resolvereports.
• Electrical: voltage spike, sensor fault, or PCB anomaly. India’s grid carries more voltage fluctuation than many appliance design tolerances assume, and a routine surge or sag can be enough to throw F6. If you’ve had recent voltage events (lights flickering, AC tripping), start your investigation here. A working stabilizer prevents this entire category.
• Software / configuration: stuck child-lock, demo-mode, or pending firmware reset.Less common but the cheapest fix when it applies — a 60-second factory reset clears it. We list this last because it’s rarely the actual cause, but check it before disassembling anything.

Safety first

Step-by-step fix

1. 1

   Step 1

   Switch the machine off at the main supply

   Press the power button to switch the washer off, then switch it off at the wall socket or pull the plug. Godrej's error table for F6 starts with exactly this: turn the machine off from the main supply. Leave the lid closed and the clothes where they are.

2. 2

   Step 2

   Wait 5 minutes, then restart

   The manual says to restart the machine after 5 minutes. Switch on at the socket, press the power button, and start the programme again. If the supply has come back to normal in that time, F6 does not return and the wash carries on.

3. 3

   Step 3

   Check whether the supply in your home is low right now

   Look for the signs of a weak supply: lights dimmer than usual, fans running slow, a stabiliser or inverter showing low input. If you have a plug-in voltage monitor, read the socket the washer uses. Godrej's troubleshooting page also lists 'Check if the power supply voltage is too low' for a machine that will not wash, so the supply is the first thing to look at.

4. 4

   Step 4

   Plug straight into a proper wall socket

   Godrej's safety page asks for a dedicated power outlet with reliable grounding: 230V, 6A for non-heater models and 230V, 16A for heater models. Take the washer off any extension board or multi-plug and plug it into its own wall socket. The same page asks you to clean the power plug regularly to prevent poor contact, so check the plug pins are clean and the plug sits firmly.

5. 5

   Step 5

   Wait for the supply to settle before washing

   The manual says F6 should disappear automatically when the voltage supply is back to normal. If the low voltage lasts for hours, run the wash later in the day when the supply is steadier, rather than restarting the machine again and again.

6. 6

   Step 6

   Call Godrej service if F6 shows with a normal supply

   If F6 keeps appearing when the supply in your home is normal and other appliances are running fine, call Godrej service. The manual's service note says: if the issue doesn't get resolved, call service engineer. The call centre number printed in the manual is 080-6743-6743. Keep your model number (on the rating label) ready.

Fixed it? Protect it next time. See an extended warranty plan for your Washing Machine →

Common mistakes Godrej Washing Machine owners make with error F6

These six anti-patterns turn a routine 30-minute fix into a costly repair or warranty void. Read before starting.

• Forcing a stuck door, lid, or panel. A Godrej Washing Machine uses interlocked sensors that hold the unit shut while it is in a fault state. Forcing it usually breaks the latch or sensor — turning a small part replacement into a full service call. If the door won’t open, run the safety-disconnect step first, then try again.
• Repeated unplug-and-replug as a “reset” ritual. Cycling power three or four times without diagnosing the underlying cause stresses the PCB and can convert a soft fault into a permanent firmware-corruption code. Reset once, observe whether the error returns immediately, then move to actual diagnosis if it does.
• Pouring water (or any liquid) into electronics-adjacent areas to flush a blockage.Even a small amount near the PCB or main wiring harness can cause permanent damage that voids warranty. The unit’s drainage paths exist for a reason; if a blockage isn’t cleared by the manual procedure, it isn’t getting cleared by improvisation either.
• Skipping the safety-disconnect step.“I’ll just check quickly” is the most expensive sentence in appliance repair. Working live on a 230V circuit (especially with a hot or wet appliance) carries real shock risk and instantly voids any warranty claim. Disconnect, wait two minutes for capacitor drain, then proceed.
• Buying counterfeit replacement parts on Amazon.in. Red flags: price below 60% of Godrej authorised price, generic packaging without a model-compatibility list, seller name that doesn’t match a known Godrej parts distributor, listings dated within the last 30 days with no reviews. Counterfeit parts often work for 2-3 weeks then fail with a different error, costing you double.
• Calling an “independent” technician for a warranty-covered unit. Indian appliances under Godrej warranty must be serviced by authorised technicians or the warranty voids permanently. Even if the warranty is expired, third-party local technicians often replace working parts to inflate the bill — verify each part swap by asking to see the failure on the old part before they install the new one.

Preventing future F6 on your Godrej Washing Machine

The fix above resolves the current instance. These five maintenance habits prevent it from coming back, specific to Godrej Washing Machines in Indian operating conditions (hard water, voltage variability, monsoon humidity).

• Monthly: clean the drain filter and inlet strainer. Hard-water deposits and everyday debris are a frequent cause of recurring F6 in India, and a few minutes each month is the cheapest way to avoid a repeat.
• Quarterly: descale water-touching components. Use food-grade citric acid or a Godrej approved descaler for hard-water regions (Bangalore, Hyderabad, large parts of Maharashtra and Tamil Nadu). Skipping this in a hard-water zone shortens the life of the heating and water-touching parts.
• Run the unit through a working stabilizer. A mainline stabilizer sized for Washing Machines is the cheapest protection against voltage-induced F6 occurrences. The MCB on your distribution board is not a substitute — it trips on overload, not on under-voltage or surge.
• Decide AMC vs DIY honestly. Compare the GodrejAMC quote against what you have actually spent on service. If your unit is >5 years old and you’ve had two service calls in the last 18 months, an AMC usually pays for itself. Younger units with no service history: DIY plus stabilizer is cheaper.
• Watch monthly for early-warning signs. Unusual noise during a specific cycle phase, water spotting, mild burning smell — any of these means a service call within a week, not a wait-and-see month. Catching F6-precursor symptoms early turns a major repair into a routine maintenance visit.

If error F6 returns within 30 days of completing the fix above, escalate directly to Godrejauthorised service — repeat patterns within a month indicate a deeper fault (worn bearing, failing PCB, leak that wasn’t fully identified) that surface-level repair won’t resolve. Document the dates and circumstances of each occurrence; the service centre will use this to prioritize root-cause investigation.