How to Fix Daikin Air Conditioner Error A6

What error A6 means

Error A6 on a Daikin air conditioner means a fan motor fault on the indoor unit. That is the wording in Daikin India's own error-code table and in the Daikin room air conditioner operation manual, which both list A6 under INDOOR UNIT with the meaning FAN MOTOR FAULT. The indoor fan is the blower that draws room air through the filters, across the cold coil and back out; when the indoor board cannot run it as commanded, the unit stops, because air that is not moving over the coil cannot be cooled and the coil itself can ice up. A6 sits with the other indoor-unit codes in the same table: A1 is indoor PCB defectiveness, A5 freeze-up protector, C4 a faulty heat exchanger temperature sensor and C9 a faulty suction air temperature sensor. The outdoor fan has its own code, E7, listed under OUTDOOR UNIT as DC fan motor fault.

Why error A6 happens on a Daikin Air Conditioner

On a Daikin Air Conditioner, error A6typically resolves to one of three root-cause categories. They’re ordered cheapest-to-verify first — start at the top and only escalate if the first cause is ruled out.

• Mechanical: blockage, obstruction, or worn moving part. A common cause across Daikin Air Conditioners in India — air filters clog and fan bearings and drain lines collect dust and sludge. Our step-by-step fix below targets this category first because it’s the cheapest to verify and resolvereports.
• Electrical: voltage spike, sensor fault, or PCB anomaly. India’s grid carries more voltage fluctuation than many appliance design tolerances assume, and a routine surge or sag can be enough to throw A6. If you’ve had recent voltage events (lights flickering, AC tripping), start your investigation here. A working stabilizer prevents this entire category.
• Software / configuration: stuck child-lock, demo-mode, or pending firmware reset.Less common but the cheapest fix when it applies — a 60-second factory reset clears it. We list this last because it’s rarely the actual cause, but check it before disassembling anything.

Safety first

Step-by-step fix

1. 1

   Step 1

   Read the code from the remote the way Daikin describes

   Daikin's remote can pull the stored code from the indoor unit. Point the remote at the indoor unit, hold the CANCEL button for about 5 seconds until 00 blinks in the temperature display, then press CANCEL repeatedly. Each press changes the code shown; a short beep means that code does not apply, and a long beep means the displayed code is the one the unit has logged. Write that code down. To leave the display, hold CANCEL for about 5 seconds again, or wait a minute and it cancels itself.

   Pro tip: Do this before resetting anything. Once the breaker has been off, the stored code may be gone and the technician has less to go on.

2. 2

   Step 2

   Clean the filters and clear the air paths

   With the breaker off, open the front panel of the indoor unit and take out the air filters. Wash them, let them dry fully and refit them. Check that nothing is blocking the air inlet at the top of the indoor unit or the outlet at the bottom, and that curtains or furniture are not sitting against it. Then look at the outdoor unit: clear leaves, bags or debris from its grille and make sure nothing is stacked against it. Daikin's manual lists dirty filters and blocked inlets or outlets as the first things to check when the operation lamp blinks and the unit stops.

   Caution: Switch off at the breaker before opening the front panel or putting your hands near the outdoor unit.

3. 3

   Step 3

   Look at the blower wheel through the filter opening

   With the breaker still off and the filters out, shine a torch through the filter opening at the long blower wheel inside the indoor unit. A thick carpet of dust on its blades, or something lodged in it, can stop the fan from reaching speed. Clear what you can reach without tools and without forcing anything. Do not remove the indoor unit's cover or its electrical box to get further in.

   Caution: Do not put your fingers or any tool into the blower wheel while there is any chance of power, and do not remove the indoor unit's electrical cover.

4. 4

   Step 4

   Switch off at the circuit breaker and restart

   Switch the AC off with the remote, then switch off its circuit breaker (MCB) and leave it off for at least 5 minutes so both boards fully discharge. Switch the breaker back on and start the AC in Cool mode with the remote. Daikin's own troubleshooting for an indoor unit whose operation lamp is blinking is exactly this: clean the filters, clear any obstruction at the air inlet or outlet of either unit, then restart with the remote, and if the lamp is still blinking, check the error code and consult the service centre. The manual also notes that lightning or radio waves can upset the unit, and that turning the breaker off and on is the remedy.

   Caution: Do not keep resetting the AC over and over if the code returns each time. Each restart puts the same component through the same fault.

5. 5

   Step 5

   Restart and listen to the indoor fan

   Start the AC in Cool mode and listen at the indoor unit. The fan should spin up smoothly within the first minute and air should come out of the outlet. Note what you hear: a fan that never starts, one that hums without turning, one that stops and starts, or one that rubs or rattles. If A6 does not return within an hour, the trip was most likely dust or an obstruction you have now cleared. If it returns, stop here and read the code again from the remote.

   Pro tip: A fan that starts and then cuts out a few minutes later is worth mentioning to the technician; it narrows the diagnosis.

6. 6

   Step 6

   Book Daikin authorised service

   A repeating A6 points to the indoor fan motor or the board that drives it, which is not a home repair. Daikin's manual says plainly that if an error code displays, you should consult your service centre. Call Daikin India customer care with the model number from the indoor unit label, the code A6 and the notes you made. If the unit is within its warranty period, use Daikin authorised service only, so the warranty stays intact.

   Caution: Never open the outdoor unit's electrical box or the indoor unit's electrical cover yourself. The inverter boards carry mains voltage and hold a charge after switch-off.

Fixed it? Protect it next time. See an extended warranty plan for your Air Conditioner →

Common mistakes Daikin Air Conditioner owners make with error A6

These six anti-patterns turn a routine 30-minute fix into a costly repair or warranty void. Read before starting.

• Forcing a stuck door, lid, or panel. Prising open a Daikin Air Conditioner housing while it is in a fault state. Forcing it usually breaks the latch or sensor — turning a small part replacement into a full service call. If the door won’t open, run the safety-disconnect step first, then try again.
• Repeated unplug-and-replug as a “reset” ritual. Cycling power three or four times without diagnosing the underlying cause stresses the PCB and can convert a soft fault into a permanent firmware-corruption code. Reset once, observe whether the error returns immediately, then move to actual diagnosis if it does.
• Pouring water (or any liquid) into electronics-adjacent areas to flush a blockage.Even a small amount near the PCB or main wiring harness can cause permanent damage that voids warranty. The unit’s drainage paths exist for a reason; if a blockage isn’t cleared by the manual procedure, it isn’t getting cleared by improvisation either.
• Skipping the safety-disconnect step.“I’ll just check quickly” is the most expensive sentence in appliance repair. Working live on a 230V circuit (especially with a hot or wet appliance) carries real shock risk and instantly voids any warranty claim. Disconnect, wait two minutes for capacitor drain, then proceed.
• Buying counterfeit replacement parts on Amazon.in. Red flags: price below 60% of Daikin authorised price, generic packaging without a model-compatibility list, seller name that doesn’t match a known Daikin parts distributor, listings dated within the last 30 days with no reviews. Counterfeit parts often work for 2-3 weeks then fail with a different error, costing you double.
• Calling an “independent” technician for a warranty-covered unit. Indian appliances under Daikin warranty must be serviced by authorised technicians or the warranty voids permanently. Even if the warranty is expired, third-party local technicians often replace working parts to inflate the bill — verify each part swap by asking to see the failure on the old part before they install the new one.

Preventing future A6 on your Daikin Air Conditioner

The fix above resolves the current instance. These five maintenance habits prevent it from coming back, specific to Daikin Air Conditioners in Indian operating conditions (hard water, voltage variability, monsoon humidity).

• Monthly: wash the air filters and clear the drain line. Hard-water deposits and everyday debris are a frequent cause of recurring A6 in India, and a few minutes each month is the cheapest way to avoid a repeat.
• Quarterly: descale water-touching components. Use food-grade citric acid or a Daikin approved descaler for hard-water regions (Bangalore, Hyderabad, large parts of Maharashtra and Tamil Nadu). Skipping this in a hard-water zone shortens the life of the heating and water-touching parts.
• Run the unit through a working stabilizer. A mainline stabilizer sized for Air Conditioners is the cheapest protection against voltage-induced A6 occurrences. The MCB on your distribution board is not a substitute — it trips on overload, not on under-voltage or surge.
• Decide AMC vs DIY honestly. Compare the DaikinAMC quote against what you have actually spent on service. If your unit is >5 years old and you’ve had two service calls in the last 18 months, an AMC usually pays for itself. Younger units with no service history: DIY plus stabilizer is cheaper.
• Watch monthly for early-warning signs. Unusual noise during a specific cycle phase, water spotting, mild burning smell — any of these means a service call within a week, not a wait-and-see month. Catching A6-precursor symptoms early turns a major repair into a routine maintenance visit.

If error A6 returns within 30 days of completing the fix above, escalate directly to Daikinauthorised service — repeat patterns within a month indicate a deeper fault (worn bearing, failing PCB, leak that wasn’t fully identified) that surface-level repair won’t resolve. Document the dates and circumstances of each occurrence; the service centre will use this to prioritize root-cause investigation.