How to Fix Daikin Air Conditioner Error E8

What error E8 means

Error E8 on a Daikin air conditioner means overcurrent input on the outdoor unit. That is the wording in Daikin India's own error-code table and in the Daikin room air conditioner operation manual, which both list E8 under OUTDOOR UNIT with the meaning OVERCURRENT INPUT. In plain terms, the outdoor unit measured more current coming in from the mains than it is allowed to draw and stopped to protect itself. Daikin's table has a separate code for the other side of the drive: L5, output overcurrent, is too much current going out to the compressor, while E8 is about the input from the supply. E8 sits with the other outdoor-unit codes in the same table: E1 circuit board fault, E5 OL started, E6 faulty compressor start up, E7 DC fan motor fault. Daikin's manual says that if an error code displays, you should consult your service centre.

Why error E8 happens on a Daikin Air Conditioner

On a Daikin Air Conditioner, error E8typically resolves to one of three root-cause categories. They’re ordered cheapest-to-verify first — start at the top and only escalate if the first cause is ruled out.

• Mechanical: blockage, obstruction, or worn moving part. A common cause across Daikin Air Conditioners in India — air filters clog and fan bearings and drain lines collect dust and sludge. Our step-by-step fix below targets this category first because it’s the cheapest to verify and resolvereports.
• Electrical: voltage spike, sensor fault, or PCB anomaly. India’s grid carries more voltage fluctuation than many appliance design tolerances assume, and a routine surge or sag can be enough to throw E8. If you’ve had recent voltage events (lights flickering, AC tripping), start your investigation here. A working stabilizer prevents this entire category.
• Software / configuration: stuck child-lock, demo-mode, or pending firmware reset.Less common but the cheapest fix when it applies — a 60-second factory reset clears it. We list this last because it’s rarely the actual cause, but check it before disassembling anything.

Safety first

Step-by-step fix

1. 1

   Step 1

   Read the code from the remote the way Daikin describes

   Daikin's remote can pull the stored code from the indoor unit. Point the remote at the indoor unit, hold the CANCEL button for about 5 seconds until 00 blinks in the temperature display, then press CANCEL repeatedly. Each press changes the code shown; a short beep means that code does not apply, and a long beep means the displayed code is the one the unit has logged. Write that code down. To leave the display, hold CANCEL for about 5 seconds again, or wait a minute and it cancels itself.

   Pro tip: Do this before resetting anything. Once the breaker has been off, the stored code may be gone and the technician has less to go on.

2. 2

   Step 2

   Switch off at the circuit breaker and restart

   Switch the AC off with the remote, then switch off its circuit breaker (MCB) and leave it off for at least 5 minutes so both boards fully discharge. Switch the breaker back on and start the AC in Cool mode with the remote. Daikin's own troubleshooting for an indoor unit whose operation lamp is blinking is exactly this: clean the filters, clear any obstruction at the air inlet or outlet of either unit, then restart with the remote, and if the lamp is still blinking, check the error code and consult the service centre. The manual also notes that lightning or radio waves can upset the unit, and that turning the breaker off and on is the remedy.

   Caution: Do not keep resetting the AC over and over if the code returns each time. Each restart puts the same component through the same fault.

3. 3

   Step 3

   Check the supply voltage and the stabiliser

   If the AC runs through a voltage stabiliser, check that it is switched on, its output reading is normal and its rating matches the AC. Check that the plug or isolator is firmly seated and not warm to the touch. If you own a multimeter and are comfortable using it, measure the socket voltage on the AC range at the time of day the code appears. A supply well outside the normal 220 to 240 V band is a reason to involve your electricity supplier or an electrician before blaming the AC.

   Pro tip: If the code only shows up during evening peak hours, or when a geyser or motor starts on the same circuit, the supply is the first suspect.

4. 4

   Step 4

   Check what else shares the AC's circuit

   An AC is meant to be on its own circuit with its own breaker. If a geyser, a water pump, an iron or a second AC has been added to the same circuit, or the AC is run from an extension board, the supply to the outdoor unit can sag and the current it draws can rise. Note what else is on the circuit and whether E8 lines up with those loads switching on. If the AC shares a circuit, have an electrician give it a dedicated one.

   Pro tip: E8 that appears only when the geyser or pump starts is a strong hint that the circuit, not the AC, is the problem.

5. 5

   Step 5

   Give the outdoor unit room to breathe

   With the breaker off, look at the outdoor unit. A condenser coil caked with dust, a fan grille blocked by leaves, plastic or a nest, or a unit boxed in so that hot air recirculates all make the outdoor side run hotter than it should. Clear anything blocking the airflow and, if the coil fins are visibly dirty, have them cleaned. Do not run the outdoor fan or compressor with the cover off.

   Caution: Switch off at the breaker before putting your hands anywhere near the outdoor fan or coil.

6. 6

   Step 6

   Restart and watch for a repeat

   Switch the breaker on and run the AC in Cool mode for an hour. If E8 does not return, the trip was most likely a one-off caused by the supply or by something you have now cleared. If E8 comes back, note how long the AC ran before it tripped, read the code from the remote again, and stop here; the remaining checks need a technician.

   Pro tip: Running the test at a higher set temperature such as 26 °C puts less load on the compressor than 18 °C does.

7. 7

   Step 7

   Book Daikin authorised service

   A repeating E8 points to the outdoor unit's drive board or the compressor it feeds, which is not a home repair. Daikin's manual says plainly that if an error code displays, you should consult your service centre. Call Daikin India customer care with the model number from the indoor unit label, the code E8 and the notes you made. If the unit is within its warranty period, use Daikin authorised service only, so the warranty stays intact.

   Caution: Never open the outdoor unit's electrical box or the indoor unit's electrical cover yourself. The inverter boards carry mains voltage and hold a charge after switch-off.

Fixed it? Protect it next time. See an extended warranty plan for your Air Conditioner →

Common mistakes Daikin Air Conditioner owners make with error E8

These six anti-patterns turn a routine 30-minute fix into a costly repair or warranty void. Read before starting.

• Forcing a stuck door, lid, or panel. Prising open a Daikin Air Conditioner housing while it is in a fault state. Forcing it usually breaks the latch or sensor — turning a small part replacement into a full service call. If the door won’t open, run the safety-disconnect step first, then try again.
• Repeated unplug-and-replug as a “reset” ritual. Cycling power three or four times without diagnosing the underlying cause stresses the PCB and can convert a soft fault into a permanent firmware-corruption code. Reset once, observe whether the error returns immediately, then move to actual diagnosis if it does.
• Pouring water (or any liquid) into electronics-adjacent areas to flush a blockage.Even a small amount near the PCB or main wiring harness can cause permanent damage that voids warranty. The unit’s drainage paths exist for a reason; if a blockage isn’t cleared by the manual procedure, it isn’t getting cleared by improvisation either.
• Skipping the safety-disconnect step.“I’ll just check quickly” is the most expensive sentence in appliance repair. Working live on a 230V circuit (especially with a hot or wet appliance) carries real shock risk and instantly voids any warranty claim. Disconnect, wait two minutes for capacitor drain, then proceed.
• Buying counterfeit replacement parts on Amazon.in. Red flags: price below 60% of Daikin authorised price, generic packaging without a model-compatibility list, seller name that doesn’t match a known Daikin parts distributor, listings dated within the last 30 days with no reviews. Counterfeit parts often work for 2-3 weeks then fail with a different error, costing you double.
• Calling an “independent” technician for a warranty-covered unit. Indian appliances under Daikin warranty must be serviced by authorised technicians or the warranty voids permanently. Even if the warranty is expired, third-party local technicians often replace working parts to inflate the bill — verify each part swap by asking to see the failure on the old part before they install the new one.

Preventing future E8 on your Daikin Air Conditioner

The fix above resolves the current instance. These five maintenance habits prevent it from coming back, specific to Daikin Air Conditioners in Indian operating conditions (hard water, voltage variability, monsoon humidity).

• Monthly: wash the air filters and clear the drain line. Hard-water deposits and everyday debris are a frequent cause of recurring E8 in India, and a few minutes each month is the cheapest way to avoid a repeat.
• Quarterly: descale water-touching components. Use food-grade citric acid or a Daikin approved descaler for hard-water regions (Bangalore, Hyderabad, large parts of Maharashtra and Tamil Nadu). Skipping this in a hard-water zone shortens the life of the heating and water-touching parts.
• Run the unit through a working stabilizer. A mainline stabilizer sized for Air Conditioners is the cheapest protection against voltage-induced E8 occurrences. The MCB on your distribution board is not a substitute — it trips on overload, not on under-voltage or surge.
• Decide AMC vs DIY honestly. Compare the DaikinAMC quote against what you have actually spent on service. If your unit is >5 years old and you’ve had two service calls in the last 18 months, an AMC usually pays for itself. Younger units with no service history: DIY plus stabilizer is cheaper.
• Watch monthly for early-warning signs. Unusual noise during a specific cycle phase, water spotting, mild burning smell — any of these means a service call within a week, not a wait-and-see month. Catching E8-precursor symptoms early turns a major repair into a routine maintenance visit.

If error E8 returns within 30 days of completing the fix above, escalate directly to Daikinauthorised service — repeat patterns within a month indicate a deeper fault (worn bearing, failing PCB, leak that wasn’t fully identified) that surface-level repair won’t resolve. Document the dates and circumstances of each occurrence; the service centre will use this to prioritize root-cause investigation.